Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Coppell
Gate parts and welding in Coppell usually means one of three things: a hinge post has heaved out of plumb, a weld has cracked on an ornamental iron gate, or the operator burned out because the gate started dragging. Most of those jobs run $240-$680 and we can often be on-site within a day or two. If your HOA is involved, the real question isn’t the weld itself. It’s whether the fix matches the original iron profile and finish specs the architectural review board approved back when the neighborhood was built. Hal Gatewood has worked on Coppell gates since 2001, and he knows the answer before he lifts the welding hood. Call (936) 296-2568 and you’ll get Hal or one of his crew, not a voicemail.
Why Gatewood Fence & Gate Is Coppell’s Preferred Gate Parts & Welding Company
Coppell isn’t just another suburb to us. The concentration of HOA-governed communities here means almost every gate repair has a second customer at the table: the architectural review board. We’ve stood in driveways along Bethel Road and Sandy Lake Road where a gate that looked fine to the homeowner would have failed inspection because the hinge barrel didn’t match the original profile. Hal’s name is on the shop and on every invoice, and that has mattered to Coppell homeowners for over two decades. When a Northlake Woodlands resident calls about a dragging swing gate, the person who shows up understands that the root cause is usually Blackland Prairie clay heaving the post, not a bad hinge leaf. The Gate Parts & Welding work we do here is repair-first because replacing an ornamental iron gate in a master-planned community means re-opening an architectural approval file that some HOA boards keep for 30 years. Our 90-Day Done Right Promise is in writing on every job. If the weld fails or the post settles again, one call brings Hal back, no runaround.
Our Gate Parts & Welding Services in Coppell
Hinge Replacement
Coppell’s late-80s and early-90s subdivisions are full of ornamental iron driveway gates whose original hinges are now three decades old. When a hinge post heaves on the clay, the hinge leaf bends or the barrel ovalizes, and suddenly the gate drags an inch at the strike side. In Coppell we regularly see hinge assemblies that look fine until you unbolt them: the pin is galled, the barrel is egged out, and the gate has been slowly eating the post base. We cut the old hardware off, plate and re-drill the post, and weld on new greasable hinge assemblies that match the original iron profile. Most hinge replacements in Coppell run $310-$580 depending on gate weight and post condition.
Post Replacement
This is the single most common structural repair we do in Coppell communities like Northlake Woodlands and near Coppell Greens. The high-shrink, high-swell clay moves posts seasonally, and a post that was plumb in March can be out by three-quarters of an inch by August. We set new posts with a concrete collar deep enough to resist heave, re-hang the existing gate leaf, and re-weld the hinge assembly to match original spacing. If the underground conduit is damaged, we replace it rather than splicing wire that will fail again in two seasons. A full post replacement with re-hanging generally runs $420-$750 in Coppell, and we quote the exact number before any work starts.
Rail Repair
On older ornamental iron gates, the top and bottom rails crack at the picket-to-rail joints after decades of thermal cycling between Coppell summers and the occasional hard freeze. A hairline crack at a weld becomes a broken rail, and a broken rail turns a driveway gate into a hazard. We grind the cracked joint back to clean metal and re-weld it, usually with a gusset plate if the original design allows. If the HOA specs require a seamless finish, we grind and blend the weld to match the adjacent profile and then match the original paint or powder coat. Rail repair in Coppell typically runs $180-$360 per rail depending on length and finish requirements.
Custom Welding
Sometimes the right fix is a custom fabrication: a rusted-out section of picket replaced with matching stock, a receiver hitch added, a gate leaf widened to match a driveway apron. Coppell HOAs are specific about this work. The replacement section has to match the original iron profile and finish, and that means the welder has to understand the difference between a stock 5/8-inch square picket and the custom-drawn profile a builder used in 1994. Hal fabricates on site, in your driveway, so the gate never leaves your property and the HOA board can see the work as it happens. Custom welding in Coppell runs $90-$130 per hour plus materials, and we quote the full job before we strike an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Coppell
We’re certified on nine major gate operator brands, but in Coppell the ones we see most are Viking and Linear swing operators from original 1990s installations, plus FAAC and BFT units added in the 2000s. When we replace a board or a gearbox, we stock common parts locally so a Coppell job doesn’t stall for a week waiting on a distributor in another state. We also service early LiftMaster swing models, Ghost Controls, and Mighty Mule, along with DoorKing and Elite. The operator matters, but the weld and the post matter more. A new Viking motor bolted to a heaving post will fail the same way the old one did.
Common Gate Parts & Welding Problems We See in Coppell Homes
- Clay heave racks hinge posts out of plumb. When a post moves even half an inch, the gate leaf drags and the operator works against the load. The motor burns out, but the real repair is the post and hinge, not the gearbox.
- No-sleeve conduit in older subdivisions crushes control wiring. Along Bethel and Sandy Lake roads, original underground gate wiring was often backfilled directly in clay with no conduit sleeve. Water intrusion and clay movement crush the wire, tripping the loop detector and killing keypad entry. A full conduit replacement is usually the fix, not a wire splice.
- Ornamental iron cracks at picket-to-rail welds. Thirty years of Coppell heat expansion and winter contraction eventually cracks the original welds on pickets and rails. We grind, re-weld, and refinish to match HOA specs.
- Slide gate rollers fail because rubber wheel seals split in the heat. Coppell summers push pavement temperatures well past 100°F, and rubber seals on slide gate rollers crack within a few seasons. We replace roller assemblies with upgraded all-metal bearings that survive Coppell summers without splitting.
Pricing for Gate Parts & Welding in Coppell, TX
Here’s what Coppell homeowners can expect to pay for the most common gate parts and welding repairs. These are our actual Coppell ranges, not a generic DFW average:
- Hinge replacement: $310-$580
- Post replacement with re-hang: $420-$750
- Rail repair or re-weld: $180-$360 per rail
- Custom welding/fabrication: $90-$130 per hour plus materials
- Gate roller replacement: $140-$260
- Latch and lock replacement: $120-$240
What affects the price in Coppell specifically: whether the HOA requires a full architectural review before work begins, whether the post base is set in undisturbed clay or backfill, and whether the existing conduit can be saved. We give you a written quote before any work starts, and the price we quote is the price you pay. No trip charge inside the county. $40 off any repair over $200. A permanent 10% discount for seniors and veterans. Call (936) 296-2568 and we’ll come take a look.
We Also Serve Cities Near Coppell
Most of our Coppell work brings us through Coppell and the surrounding DFW suburbs. We do regular gate parts and welding work in Addison, Richardson, Plano, and Dallas too. If your community is close to Coppell, call us: the same crew, the same written promise, the same live person on the phone.
Serving Coppell, TX - Our Local Coverage Area
We’re based in the Coppell area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Coppell
Yes, in almost every Coppell HOA-governed community, welding a new gate onto existing posts requires architectural review board approval first. The board typically wants to see the proposed gate’s material, finish, height, and profile to confirm it matches the original community standard. We can prepare a specification sheet for your HOA that includes the weld details, the replacement hardware, and the finish color. Call (936) 296-2568 and we’ll help you put together what the board needs.
Yes, we do this all the time in Coppell Greens and similar subdivisions. The original ornamental iron gate leaf is usually still good. The post is the problem. We cut the gate off at the hinges, dig out the old post, set a new one with a concrete collar sized to resist Blackland Prairie heave, and re-weld the original hinge assembly back onto the post at the same spacing. The gate keeps its original profile, which is exactly what the HOA wants to see.
Your hinge post is heaving on the clay. In spring, the soil is moist and expanded, so the post sits taller and the gate clears. By August, the clay shrinks and the post settles, which drops the gate leaf and makes it bind at the strike. The fix is resetting the post with a deeper footing and a concrete collar, then re-welding the hinges. Replacing the operator won’t fix it. We quote the post work upfront and often handle the whole repair in one day.
It depends on what the HOA has already approved, but in most Coppell communities, replacing just the rack and pinion is an allowed repair as long as the replacement parts match the original gate profile and the drive system’s entrapment protection remains functional. We’ll tell you honestly whether the rack is the only problem or whether the motor and gearbox are also at end of life. Call (936) 296-2568 and describe the gate. We’ll give you a straight answer.
Yes. We can mount a photocell on the existing post or rail using surface-mount brackets that don’t require drilling into the gate’s ornamental iron. The wiring can run inside the existing post or through a color-matched conduit that satisfies most Coppell HOA finish requirements. Safety sensors are worth doing right: an older swing gate without entrapment protection is a genuine hazard, and current safety standards didn’t exist when many Coppell gates were installed. We’ll add the photocell without changing the gate’s original appearance.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Coppell since 2001.