Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across North Dallas
Gate parts and welding in North Dallas usually come down to one question: repair the existing steel or replace it. We repair it. A gate hanging out of plumb on a tilted masonry column, a slide gate jumping its track after a spring storm, a hinge post that has been shearing anchor bolts for a decade. Those are North Dallas problems. Our crews carry the steel, the welders, and the parts to fix them on site, and we answer the phone at (936) 296-2568. No voicemail, no call center three states away. You call, a person picks up.
We have been at this long enough to know North Dallas gates fail a certain way. We will get into that below. But if you have a gate that won’t close properly or a post leaning out of square, the first step is a real inspection of the steel and the post, not a quote for a whole new operator.
Why Gatewood Fence & Gate Is North Dallas’s Preferred Gate Parts & Welding Company
Hal Gatewood has been fixing gates since 2001, and his name is on the shop and on every invoice. That matters here. North Dallas homeowners have already been quoted one price on the phone and another at the door, by companies with a national name and no local face. Hal publishes an address and a license number anyone can look up. The person who gives you the estimate is the person who stands behind the work.
Reviews from North Dallas customers mention the same things. The person who showed up was the person they had talked to. The weld work looked like steel work, not a patch. And when something needed attention inside the 90-Day Done Right Promise, one call brought Hal back. No runaround. The promise is in writing on every job, including parts and welding work in North Dallas. We also offer a free second opinion on any written estimate, and there is no trip charge inside the county. A permanent 10% discount for seniors and veterans is another thing we just do, without being asked.
Dallas-Fort Worth scheduling coordinates our local crews, so a North Dallas call gets a North Dallas response, typically the same day for emergency welding and hinge work. If a gate is hanging off a single hinge, that is an emergency. We treat it like one.
Our Gate Parts & Welding Services in North Dallas
Hinge Replacement
Older North Dallas swing gates, especially the 1980s and 1990s ornamental steel ones in Prestonwood and Bent Tree, were often hung on hinges that have now been carrying 300 to 800 pounds of steel for 30 years. The hinge barrel wears oblong, the gate sags, the latch misses, and the operator keeps tripping its obstruction sensor. We replace hinges with heavy-gauge units matched to the gate’s weight, and we weld them better than the original.
Post Replacement
This is the North Dallas special. Blackland Prairie clay swells in wet winters and shrinks in August, and every cycle tilts a hinge post another fraction of an inch. When a post is leaning 2 to 4 inches, the gate is fighting gravity before the operator even powers on. We remove the old post, dig a deeper footing, set a new post plumb, and weld the gate back on square. We do not shim a leaning post and call it fixed. A gate sags in the hinge post, not in the middle, and that is where we start.
Rail Repair
Slide gates in North Dallas take a beating. A high-velocity spring storm bends the track, a wheel hangs up, and the gate grinds and jumps. We straighten or replace rail sections, splice new track where the old is worn through, and re-weld the frame so the gate rides smooth again. Most rail repair happens in the driveway, on site, with our welder and our steel. We are not hauling a gate across town for something that should be fixed where it stands.
Custom Welding
Gate parts break. Brackets snap. A keypad mount from fifteen years ago doesn’t fit a new panel. A solar gate opener needs an arm welded to a finial that was never designed for it. We custom-fabricate brackets, mounts, reinforcement plates, and repair sections for whatever North Dallas threw at your gate. We weld on site, which means no week-long wait while your gate sits in someone else’s shop. See our full Gate Parts & Welding capabilities, or call (936) 296-2568 and describe the part. Hal can usually tell you over the phone whether it is a repair or a replacement.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in North Dallas
We work on Viking, Linear, DoorKing, and Ghost Controls systems regularly, along with several other major brands. We stock parts for these operators in our local inventory, so a North Dallas repair doesn’t have to wait on a factory shipment from the coast. Whether the gate itself is an old ornamental steel swing in Preston Hollow or a commercial-grade slide gate on an HOA entrance near the Dallas North Tollway, we match the part to the system and to the gate’s actual weight.
Common Gate Parts & Welding Problems We See in North Dallas Homes
- Post heave and tilt. North Dallas sits on Blackland Prairie clay that can swell several inches in a wet winter and shrink in a summer drought. A hinge post leaning 2 to 4 inches throws the entire gate out of mesh, so the operator’s limit switches and safety loops stop working. The operator is often fine; the post is not.
- Heat warped frames and dry bearings. A 100°F North Dallas summer bakes black steel until it moves. Weld points crack, frames warp, and lubricant dries to dust. We see more stress fractures in July and August than the rest of the year combined.
- Freeze damage to masonry columns. The February 2021 freeze cracked columns all over North Dallas. Masonry shifts, hydraulic operators seize, and the gate binds. One hard freeze does what ten summers chip away at.
- Storm bent tracks and knocked-off hinges. Spring and fall straight-line winds push hard against wide steel gates. A slide gate track gets bent, or a swing gate lifts off a worn hinge. Homeowners mistake the resulting misalignment for an operator failure. It is usually steel or track.
Pricing for Gate Parts & Welding in North Dallas, TX
A hinge replacement in North Dallas typically runs $150 to $420, depending on the gate’s weight and whether the post also needs attention. Post replacement, including new steel, concrete footing, and weld work, is usually $600 to $1,800. Rail repair on a bent slide gate is generally $300 to $900. Custom welding brackets or mounting arms run $120 to $450 per piece. Every price is quoted and agreed before we start. You will know the number before the first weld. Estimates are free, and there is no trip charge inside the county. Call (936) 296-2568 and we will come look at the gate, walk you through what it needs, and hand you a written price. Hal has $40 off any repair over $200, so a hinge or rail job often gets cheaper from the first call.
We Also Serve Cities Near North Dallas
Our Gate Parts & Welding in North Dallas crews spend most of the week in North Dallas proper, but we also run calls into University Park, Plano, Irving, and the surrounding Dallas neighborhoods. If you are a few minutes outside North Dallas and have a gate leaning hard or a track bent in the last storm, call anyway. We will tell you straight whether we can get there the same day.
Serving North Dallas, TX - Our Local Coverage Area
We’re based in the North Dallas area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in North Dallas
Nine times out of ten in North Dallas, it is the hinge post. The Blackland Prairie clay under this part of the city swells and shrinks, slowly tilting the post out of plumb until the gate sags and the operator’s obstruction sensor trips every cycle. We check post plumb first, before we touch electronics. Fix the panel without the post and you will fix it twice. Call (936) 296-2568 for a free inspection.
Yes, in most cases. An older FAAC or Elite operator can usually be retrofitted with current safety photocells, edges, and control boards that meet UL 325 standards. Some very old boards are obsolete and replacement is genuinely cheaper than trying to source a discontinued part. We will show you both numbers and let you decide. Estimates are free, and Hal offers a second opinion on any written quote you already have from another company.
Usually yes, if the track is bent or a rail splice has separated. A slide gate that jumps the track after every high-wind storm in Prestonwood has a mechanical problem that tightening bolts will not solve. We weld the rail seam, straighten or replace the bent track section, and reset the wheels so the gate rides true again. It is a same-day repair in most North Dallas cases. Call (936) 296-2568 and describe what the gate does.
We remove the gate, pull the old hinge post, dig a deeper footing, and set a new post plumb in fresh concrete. Then we re-hang the gate on new heavy-gauge hinges, weld the frame square, and only then recalibrate the operator. Quoting an operator swap without checking column plumb is the fastest way to waste money on a North Dallas gate. The operator is usually fine; the frame and post are fighting each other.
Yes. We fabricate and weld custom brackets for keypads, solar panels, opener arms, and lock housings on ornamental steel and tubular gate frames. Older North Dallas gates often have finials and scrollwork that were never designed for any kind of mounting point, so a custom welded bracket is the only way to add modern access control without damaging the gate. Call (936) 296-2568 for an exact price, and remember estimates are free.
If your North Dallas gate is leaning, sagging, jumping track, or the operator has stopped talking to the sensors, call (936) 296-2568. Someone will answer. Hal will likely be the one to come look at it, and the price will be on paper before any weld or part goes in. The name is on the shop, and the shop serves North Dallas. That is the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving North Dallas since 2001.