Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Highland Park
Gate parts and welding in Highland Park usually means one of three things: a hinge post that black clay soil has shoved out of plumb, a custom wrought iron panel that needs a weld repair nobody stocks parts for, or a heavy slide gate whose rollers have ground themselves flat. We handle all three on site, and most Highland Park calls get same-week service because our crews stage out of the Dallas-Fort Worth metro. Hal Gatewood has been welding and rebuilding gates since 2001, and when he quotes a price, that’s the price. Call (936) 296-2568 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Highland Park’s Preferred Gate Parts & Welding Company
Highland Park isn’t like the suburbs that spread out flat and predictable. The lots are old, the trees are enormous, and the gates are heavy. Half the repairs our Gate Parts & Welding crew does in this town start with someone else’s previous work: a hinge post set too shallow, a weld that looked fine until the first summer, an operator bolted to a pier that was already leaning. Hal’s name is on the shop and on every invoice. He’s not passing through.
What builds trust here isn’t a marketing pitch. It’s showing up with a welding rig in the driveway, cutting out only what’s broken, and leaving the original scrollwork alone. Highland Park homeowners tend to ask pointed questions and check references. We’re used to that. The 90-Day Done Right Promise is in writing on every job. Reviews from Highland Park customers consistently mention the same things: clear pricing before work starts, no upsell on parts that don’t need changing, and a repair that actually holds through the next wet-dry cycle.
Our Gate Parts & Welding Services in Highland Park
Hinge Replacement
Hinges on Highland Park estate gates fail because the load never lets up. A 16-foot wrought iron panel hanging on two hinges exerts force constantly, and when the post shifts even a quarter inch, the hinge pins wear oblong. We remove the old hinge, weld in new plate steel as needed, and reset the panel so it swings without dragging. We work with LiftMaster, FAAC, and Viking hardware on the operator side, so the hinge repair doesn’t throw the automation out of alignment.
Post Replacement
Post replacement in Highland Park is its own discipline. The clay soil heaves seasonally, and if the footing isn’t deep and wide enough, a new post is just the next post that will lean. We excavate, cut out the rotted or shifted steel, weld a new footing cage, and set the post in concrete below the frost line and below the active clay zone. On brick and limestone pilaster jobs, we cut the masonry clean, keep the column face intact where possible, and make sure the new post carries the gate’s weight without hanging it on the brick.
Rail Repair
A sagging rail will fool you. The panel drops at the latch side, and it looks like the rail bent. Sometimes it did. More often, the hinge post moved and the rail is just along for the ride. We check the post first, then the rail. If the rail is fatigued or cracked, we weld a reinforcing plate along the inside, grind it smooth, and repaint to match. On custom scrollwork and older ornamental gates, we match the original profile rather than replacing it with a generic box tube.
Custom Welding
Highland Park’s older estates have gates that don’t exist in any catalog. Built in the 1930s and 1940s by iron shops long gone, they have tapered pickets, hand-forged scrollwork, and collars that were fitted hot. Custom welding means replicating those details with modern steel and a steady hand. Hal welds on site, in your driveway, so the gate never leaves your property. If a section is beyond repair, we fabricate a match and weld it in.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Highland Park
We service and stock parts for nine major gate operator brands, and in Highland Park we see a lot of FAAC hydraulic swing operators on the older estates, BFT on the newer slide gates, and Linear on mid-sized driveway gates. We keep common parts on the truck: hinge hardware, receiver boards, limit switches, and safety edge components. If a part isn’t on hand, we can usually have it in a day or two and finish the job on one return visit. What we won’t do is swap a brand-specific operator part for a knockoff that fails in August.
Common Gate Parts & Welding Problems We See in Highland Park Homes
- Hinge posts out of plumb from clay heave. The post leans, the gate drags on the brick pilaster, and the hinge pins wear oval. Setting a new post without fixing the footing means doing the job twice.
- Tree roots cracking post footings. Live oaks and cedar elms send roots under the post footing, the footing cracks, and the post rotates. A simple hinge replacement turns into excavation and a full re-weld of the footing cage.
- Worn slide gate rollers on replated lots. New construction disturbs the soil for years. The track settles unevenly, the gate rides heavy on one roller, and the roller wears flat, scoring the rail and straining the operator.
- Solar operators stalling under canopy shade. Long driveways lined with mature trees sound great until the solar panel gets shaded by cedar elm debris. The operator loses power mid-travel, and there’s no line voltage backup. We address both the power problem and the mechanical bind.
Pricing for Gate Parts & Welding in Highland Park, TX
Highland Park pricing runs a little above Dallas averages because the gates are larger, older, and hung on heavier masonry. A hinge replacement on a single swing gate typically runs $180 to $420 depending on how much plate steel we need to rebuild at the post. Post replacement with excavation and a new welded footing cage runs $650 to $1,400, higher if we’re resetting limestone or brick veneer. Rail repair and welding range from $150 for a small crack to $900 for a full rail replacement on a 16-foot panel. Every price is quoted and agreed before any work starts. You’ll see the number on paper, and we don’t come back with a different one. Call (936) 296-2568 for a free estimate.
Highland Park Gate Permits: What Homeowners Need to Know
Highland Park runs its own municipal building department, entirely separate from the City of Dallas. That matters on any post replacement, pilaster rebuild, or new operator install. Work done under a Dallas permit, or with no permit at all, gets stopped by Highland Park inspectors. We handle permit-ready welding and post work on every job here. Our drawings and footing details meet Highland Park’s requirements the first time, because we’ve done this long enough to know what the inspectors look for: footing depth, post embedment, weld sizing on the hinge plates, and proper clearance between the gate and any fixed object. Hal will walk you through the permit sequence before we start, so there are no surprise stop-work orders on a property this valuable.
We Also Serve Cities Near Highland Park
If you’re just outside town, we cover University Park, Dallas, Plano, and Irving as well. A lot of our work in those areas comes from referrals out of Highland Park, and the same approach applies: repair first, replace only what’s broken, and stand behind it in writing. Call (936) 296-2568 and we’ll tell you straight what the job needs.
Serving Highland Park, TX - Our Local Coverage Area
We’re based in the Highland Park area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Highland Park
Highland Park inspectors check footing depth and diameter, post embedment, weld sizing on the hinge plates and the footing cage, and clearance between the gate panel and the pilaster or adjacent masonry. They also verify the operator’s safety edges and entrapment protection if the gate is automated. We build to those standards on every Highland Park job, permit or not. Call (936) 296-2568 and we’ll tell you exactly what your specific property will trigger.
Sometimes, but only if the post is still plumb and solid. On Highland Park’s clay soil, a sagging rail is usually a symptom of a hinge post that has moved. If the post is sound, we weld a reinforcing plate along the inside of the rail, grind it clean, and match the paint. If the post has moved, welding the rail alone won’t hold, and the gate will sag again within a season. We’ll tell you which situation you have before we recommend any work. Estimates are free.
Yes, but solar openers on Highland Park driveways have a specific problem: tree canopy. Live oaks and cedar elms shade the panel, and leaf debris accumulates on the glass. The operator loses power mid-travel, and then the gate sits there with the motor stalled. On long driveway runs, we size the solar panel for the operator’s actual draw and add a battery bank if shade is chronic. Call (936) 296-2568 and we’ll assess your gate’s power load honestly.
The rack height depends on the specific operator model, but the standard working range is 1/4 inch to 3/8 inch clearance between the rack teeth and the pinion gear at all points along the track. On replated Highland Park lots, the soil is still settling, so we weld the rack in short sections and leave room for post-settlement alignment before final welding. A rack set too tight will bind and burn out the operator motor. This is a job for a welder who understands gate automation, not a general handyman.
We re-test the full entrapment circuit: the primary and secondary safety edges, the photo eyes if installed, and the operator’s current sensing and auto-reverse function. UL 325 requires four means of safety on gate operators, and after any roller or track work, the gate’s travel path changes. A roller replacement can alter the point where the safety edge contacts an obstruction. We test everything before we leave, and the results are noted on your invoice under the 90-Day Done Right Promise.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate. Hal has welded, repaired, and rebuilt gates in North Texas since 2001.