Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterWeld & Rust Repair in University Park, TX
Weld and rust repair for residential gates in University Park typically costs between $150 and $450, depending on the severity of the corrosion and whether we need to fabricate new steel components on-site. If you notice your gate dragging, clicking, or showing visible flaking rust near the hinges or latch, it is a structural issue that requires immediate attention before the gate collapses or damages your driveway surface. We handle these repairs directly in your driveway using mobile welding equipment, ensuring you don’t have to wait for parts to be shipped or for your gate to be hauled away to a shop. For a free, honest estimate on our Gate Repair services, call us at (936) 296-2568.
I have been fixing gates in this area since 2001, and I have seen how the humidity in Texas can eat through a wrought iron or steel gate if it is not maintained. A gate that sags isn’t just an eyesore; it is a weight pulling on your posts, which can eventually warp your entire entryway. When I show up to a job, I don’t look for ways to sell you a new system. I look for the strongest way to reconnect the metal you already have. If you are looking for local Gate Repair in University Park, you want someone who treats the steel like it is their own. We stand behind every weld with a 90-Day Done Right Promise, which means if the repair does not hold, I will come back and make it right at no extra cost to you.
When You Need Weld & Rust Repair
You do not need to be a welder to know when your gate is failing. The metal usually gives you plenty of warning signs before it actually breaks. If you see any of the following, give us a call before the problem gets worse:
- Visible Flaking Rust: If you can scrape the metal with your fingernail and see orange, pitted steel underneath, the rust has already compromised the structural integrity of the gate frame.
- Gate Dragging on the Concrete: This usually happens because the hinge-side weld has snapped or the hinge post has shifted, causing the gate to drop and scrape against your driveway.
- Loose or Rattling Decorative Bars: In University Park, the summer heat causes thermal expansion, which can pop old, brittle welds on decorative scrollwork, leaving your gate looking unfinished and weak.
- Latch Misalignment: If you have to lift or push your gate to get the latch to catch, the frame has likely twisted due to a broken weld elsewhere on the structure.
- Clicking Sounds During Movement: When a gate motor is trying to pull a gate that is bound up because of a broken hinge weld, you will hear a distinct clicking or groaning from the operator.
Ignoring these signs is a safety risk. A heavy gate hanging by a single, failing weld can drop without warning, which is dangerous for children, pets, and vehicles. If you have an opener like a Viking or a DoorKing, Automatic Gate Repair expertise is important because the motor is designed to move a balanced gate. When the gate frame is broken, that motor works twice as hard, leading to premature failure of the gearbox and control board.
Our Weld & Rust Repair Process
I do not believe in taking your gate off the property unless it is absolutely necessary. We bring the shop to your curb. Here is how we handle a weld and rust repair job:
- Structural Assessment: I inspect the entire gate frame, not just the spot where the rust is visible. We look for stress cracks in the paint, which are often the first sign that a weld has failed underneath.
- Surface Preparation: We grind down the rusted areas to reach clean, bare metal. You cannot weld to rust, and painting over corrosion is a waste of time. We get down to the healthy steel every single time.
- On-Site Welding: Using our mobile welding rig, we fuse the joint back together. We focus on deep penetration welds that are stronger than the original factory tack welds often found on mass-produced gates.
- Reinforcement: If the original design was weak, we add gussets or steel bracing to distribute the weight better. This prevents the same spot from failing again in two years.
- Protective Coating: After the weld cools, we clean the area and apply a rust-inhibiting primer and a matching finish coat to seal the metal from the Texas humidity.
When you call (936) 296-2568, you are not talking to a dispatcher in a call center. You are talking to someone who knows exactly what a rusted hinge looks like and how to fix it. We are locally owned and owner-operated, and we have been at this long enough to know that doing it right the first time is cheaper for you and easier for me.
Weld & Rust Repair Pricing in University Park
We believe in upfront pricing. You should never be surprised by a bill when the work is finished. While every gate is different, here is how we generally structure our repair costs:
| Service Type | Estimated Range |
|---|---|
| Small spot weld (1-2 joints) | $150 – $250 |
| Hinge repair & reinforcement | $250 – $450 |
| Major frame rust remediation | $450+ (Quote required) |
We offer a permanent 10% discount for seniors and veterans, and we take $40 off any repair over $200. There is no trip charge inside the county, and if you have a written estimate from another company, I will give you a free second opinion. Often, I find that what other companies call a “gate replacement” is just Electric Gate Repair work that they didn’t want to take the time to do.
FAQs - Weld & Rust Repair
Is it cheaper to repair a rusted gate or replace it?
In 90% of cases, repairing the gate is significantly cheaper than replacing the entire structure. Unless the gate is completely rotted through to the point where the metal turns to powder, we can almost always weld, brace, and reinforce the existing frame to make it sturdy again. Call (936) 296-2568 and I can take a look at it to give you an honest answer on whether it is worth saving.
Can you match the paint on my gate after the weld?
We do our best to match the existing finish, but please know that sun exposure changes the color of paint over time. We use high-quality, rust-inhibiting exterior metal paint. If your gate has a custom powder coat, the repair area will be a painted surface, which is standard for on-site repairs. It will be protected from rust, though it may look slightly different than the original factory finish.
Do I need to be home for the repair?
If the gate is located on the exterior of your property, you do not necessarily need to be home, provided we have access to the gate and a power source nearby. However, I always prefer to meet the homeowner at the start of the job to show you exactly where the weakness is and what I am doing to fix it. We value transparency, and I want you to see the work before I button it up.
Does this repair include the gate opener?
This service focuses on the physical gate structure, not the electronics. However, if your gate is dragging, it puts immense strain on your opener, whether it is a Linear, Ghost Controls, or another brand. We often fix the structural issues first, which solves the “motor trouble” because the motor no longer has to drag a heavy, broken gate. If the motor itself is failing, we can troubleshoot that as part of our full home service offerings.
If you are tired of dealing with a gate that doesn’t close right or looks like it is falling apart, I am ready to help. We are locally owned and owner-operated, and we have been serving this community since 2001. You will get a real person on the phone, a clear price before we start, and a 90-Day Done Right Promise on the work. Call us today at (936) 296-2568 for a free estimate.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving University Park.