Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Farmers Branch
When a gate post pulls loose in Farmers Branch, it’s rarely just a hinge problem. It’s the Blackland Prairie clay under the footing, heaving and contracting through every rain and drought cycle until the post leans and the welds tear. We see it constantly in the 1950s and 1970s ranch neighborhoods off Valley View Lane and Marsh Lane. If your gate sags, drags, or won’t latch, call (936) 296-2568 and we’ll get a welder to your driveway for Gate Installation - Farmers Branch, usually same day. Hal Gatewood has been fixing gates since 2001, and his crew works Farmers Branch every week.
Key Takeaways
- Welding and post replacement run $180-$650 in Farmers Branch, depending on the gate and post condition.
- We stock commercial-rated control boards and rack-and-pinion for Valwood Industrial Park slide gates.
- Same-day response to Farmers Branch; a live person answers the phone 24/7.
- Free written estimates, no trip charge inside Dallas County, and a 90-Day Done Right Promise in writing.
Why Gatewood Fence & Gate Is Farmers Branch’s Preferred Gate Parts & Welding Company
Most gate companies in the metro don’t really know Farmers Branch. They drive up from Dallas or over from Irving and treat every job the same: swap the hinge, collect the check, gone. We work this area differently because the gates fail differently. The residential streets off Golfing Green Drive and Snow White Drive are full of 60-year-old wrought-iron driveway gates with footings that were never poured deep enough for North Texas clay. The commercial corridor along Stemmons is a different animal entirely: high-cycle slide gates, access control integration, burned-out operator boards. Knowing which one you’re dealing with is the whole job. Our Gate Parts & Welding team carries both: residential-grade parts for the ranch houses and commercial-rated boards and rack for the industrial park.
Hal owns the company. His name is on the shop and on every invoice. When you call about a sagging gate on a 1962 ranch off Valley View, the person who answers is somebody who can actually talk about what’s wrong with it. We’ve been welding and fabricating on site since 2001. No dispatch queue. No voicemail at 2 a.m. when your gate is stuck open and your dog is loose in the front yard. One number: (936) 296-2568.
Our Gate Parts & Welding Services in Farmers Branch
Hinge Replacement
In Farmers Branch, hinge replacement almost never stops at the hinge. The original barrel hinges on those 1950s ranch gates were welded directly to posts that have since been pushed out of plumb by decades of clay-soil movement. We cut the old rusted hinge off clean, grind the post face flat, and MIG-weld a heavier barrel hinge so the gate hangs square again. If the post itself is moving, we say so before we touch it. Fix the panel without the post and you’ll fix it twice.
Post Replacement
This is the single most common job we do in Farmers Branch. The Blackland Prairie shrink-swell cycle starts working on a gate post from the day it’s set. Thirty or forty years later, the footing has lost its grip, the post leans, and the gate drags a half-moon into the driveway. We dig out the old concrete, set a heavier-gauge steel post, and weld the gate hinges back on true. A new post in Farmers Branch typically runs $300-$650 including concrete, material, and labor.
Rail Repair
Farmers Branch ranch gates from the 60s and 70s used thin-gauge ornamental rails that rust from the inside. By the time the flaking paint shows, the lower rail has often lost a third of its wall thickness. We weld in reinforcement or replace the rail entirely, then re-mount the pickets so the whole frame carries load as one piece. A typical rail repair runs $180-$350.
Custom Welding
Not every gate is fixable with a stock part. Some of the gates on Brookhaven or along Webb Chapel Road were built by a welder in 1972 whose shop closed 30 years ago. Hal fabricates replacement sections, hinge plates, latching brackets, and full gate leafs on site. We match the old ornamental scroll work closely enough that most neighbors never notice which part is new. Custom welding is quoted by the job after we see it; most Farmers Branch fabrication work falls between $250 and $900.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Farmers Branch
We service and install Farmers Branch Gate Motor & Opener brands including FAAC, BFT, Linear, Viking, and five other major gate operator brands. For Farmers Branch, we keep a specific inventory on the truck: FAAC hydraulic operators for the older estate gates, Linear and Viking access-control cards for the commercial calls, and BFT slide-gate boards for the light-industrial entrances along Valwood Parkway. If your existing opener is made by a brand we don’t stock, we’ll tell you that up front rather than soldering a workaround that fails in July.
Common Gate Parts & Welding Problems We See in Farmers Branch Homes
- Heaved hinge posts from Blackland Prairie clay: The soil under Farmers Branch swells after spring rain and contracts hard in the triple-digit summers. That annual cycle tears base welds and leans posts. We see it worse here than in Dallas or Irving because much of Farmers Branch sits directly on the open prairie soil series.
- Fried control boards on Valwood slide gates: Industrial tenant gates run 60 to 100 cycles a day. A standard residential LiftMaster board can’t survive that. We get called out after the property manager already paid somebody to replace the board once that spring. Stocking commercial-rated boards changes that call from a repeat to a fix.
- Stripped rack-and-pinion on high-cycle slide gates: Off Valwood Parkway and along Stemmons, the original gate installs often used light-duty rack. Daily truck traffic eats it in two or three years. We replace it with heavy-gauge rack and pinion manufactured for continuous duty, not the weekend-cycle stuff.
- Corroded hinges on 50-to-70-year-old wrought-iron ranch gates: Original gate hardware from the 50s, 60s, and 70s was never galvanized. By now, the metal is electrolytically fused inside the hinge barrel. We replace the whole assembly rather than greasing rust that’s already structurally gone.
Pricing for Gate Parts & Welding in Farmers Branch, TX
Here’s what we’re charging in Farmers Branch right now, in real numbers:
| Job | Typical Range |
|---|---|
| Hinge replacement (single gate) | $180-$340 |
| Post replacement (with concrete) | $300-$650 |
| Rail repair / reinforcement | $180-$350 |
| Custom welding (per job) | $250-$900 |
| Commercial slide gate board + rack replacement | $600-$1,400 |
| Full gate fabrication | $900-$2,500 |
Every job is quoted on site, in writing, before we cut, weld, or order a single part. No dispatch, no trip charge in county, and no invoice bigger than the number we discussed. We also take $40 off any repair over $200 and offer a permanent 10% discount for seniors and veterans. Call (936) 296-2568 and tell Hal what the gate’s doing; he’ll tell you honestly whether it needs a part or a full repair, and what it’ll cost.
We Also Serve Cities Near Farmers Branch
We work Farmers Branch every week, but we also cover Farmers Branch neighbors like University Park, Dallas, Plano, and Irving. If you’re in one of those cities and the gate is down, call the same number. If it’s inside the county, same no-trip-charge policy applies.
Serving Farmers Branch, TX - Our Local Coverage Area
We’re based in the Farmers Branch area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Farmers Branch
Because the post is moving, not just the hinge. If the footing was set shallow, Blackland Prairie clay will lift it a little more every rain season and drop it again in the dry heat. Each cycle loosens the post-to-soil bond and pulls the gate frame out of square. The hinge gets blamed because it’s the part that bends. On most Farmers Branch ranch houses, the real fix is pulling the post, setting a deeper footing with a heavier steel post, then re-hanging the gate. You’ll spend $300-$650 instead of $180 for a hinge, and it’ll still be plumb in ten years. Call (936) 296-2568 and we’ll tell you which post is failing before we cut anything.
Almost certainly yes, if the gate cycles more than 50 times a day or anchors a tenant truck entrance. The light-duty boards that come with a $400 opener die under that load, usually within a year, often mid-travel with a truck waiting on Stemmons. We stock commercial-rated LiftMaster, Elite, FAAC, and BFT boards for this exact Farmers Branch call. The cost for a board and rack replacement on a commercial slide gate runs $600-$1,400. Free on-site eval, and our truck already has the parts.
Yes, but the hinge itself has to come off first. You can’t weld over a rust seam and expect it to hold through the fall. We grind the post face clean or cut the barrel entirely and weld on a new barrel hinge matched to the gate’s weight and swing. If the gate’s lower rail is also thin from internal rust, we’ll tell you before we weld, and usually we’ll reinforce it in the same visit. A typical hinge replacement and post-face repair in Farmers Branch runs $180-$340.
You size the battery and panel to the gate’s actual cycle count, and then you inspect the wiring and the lower hinge twice a year. The biggest problem we find on long-driveway gates is an undersized solar panel trickle-charging a battery that’s too small for the opener draw. A week of overcast skies drains it, the gate gets shoved open manually, and the lower hinge twists out of square. We specify and install the right panel, battery, and hinge assembly together, not separately. Most Farmers Branch solar repair and rebuild work lands between $400 and $1,000, quoted before we start.
Often, yes. The photocell’s problem is not the sensor itself; it’s the post it’s mounted to. On high-traffic slide gates in Farmers Branch, the emitter and receiver get clipped by mowers, trucks, or just wind vibration until the mounting bracket works loose, which is why proper Gate Access Control in Farmers Branch matters. We re-weld or replace the post mount, add a steel guard, and then align the beam. If the gate keeps faulting after that, the operator board’s photo-eye circuit may be failing; we test and replace that too. Estimate is free, and the fix usually runs $120-$300 plus the part if it’s needed. Call (936) 296-2568 and tell the person who answers exactly where the gate is in Farmers Branch; they’ll route the right truck.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Farmers Branch since 2001.