Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Installation in University Park: What to Know First
Linear gate installation in University Park runs $1,450 to $4,300 for a complete residential job, depending on whether it’s a single swing gate or a full double driveway system. We install and service Linear openers, control boards, and gate hardware as an independent Linear service provider, which means you get Local knowledge without the national chain markup. Around here, most full installations take one to two days once materials are on hand, and we quote the price before any work begins so there are no surprises at the door.
This page is for University Park homeowners who already own a Linear system or are considering one for a new gate. If you just learned your existing Linear opener failed and you need a straight answer, call us at (936) 296-2568. Hal Gatewood grew up not far from Goar Park, so we know how these gates behave in Dallas clay soil and hundred-degree summers.
Key Takeaways:
- We install, repair, and replace Linear gates as an independent shop, not a manufacturer subsidiary.
- Price is always quoted and agreed before work starts. Free estimates, no trip charge inside the county.
- Same-week installation is typical for standard swing and pedestrian gates.
- The 90-Day Done Right Promise is on every invoice. If it’s not right, we come back and make it right.
How Linear Products Fail, and How We Fix Them
Linear makes dependable gear, but University Park heat and soil take their toll just like anywhere else. These are the failure points we see most often in this area.
- Linear LRA actuator limit switch drift. The Linear LRA series linear actuator is a workhorse on residential swing gates, but we see limit switches drift over time. A gate that stops six inches short or slams against the post is usually the switch falling out of calibration. Fixing it means opening the actuator, cleaning the contacts, and re-setting travel limits so the gate stops soft and true.
- Linear control board capacitor failure after storm surges. University Park gets its share of summer lightning, and Linear APeX and DCM control boards are sensitive to it. A gate that hums but won’t move after a storm is often a blown capacitor on the board, not a dead motor. We test the board first before selling you a part you don’t need.
- Linear radio receiver interference from newer LED bulbs. This one surprises people. If your Linear Multi-Code 3089 remote worked fine until you swapped your porch light for an LED, the bulb’s driver may be drowning out the 318 MHz signal. We’ve cured dead remotes simply by relocating the receiver or swapping the bulb. You won’t find that in the manual.
- Mechanical wear on older Linear slide gate chains. Linear slide gate operators that use chain drives stretch over the years. A gate that lurches or grinds partway through its travel usually has a chain that needs tensioning or replacement. We keep chain kits on the truck for most common Linear models so we’re not running back and forth to a supply house.
- Battery backup failure in Linear emergency release systems. Linear gates with battery backup systems use sealed lead-acid batteries that last three to five years. When a gate works fine on AC but dies the minute power goes out, the battery is shot. We replace the battery, test the release mechanism, and make sure the gate opens manually without a fight.
Our Linear Gate Installation Process
Here’s how a Linear gate installation goes at your University Park home, from first call to final walk-through.
- 1
Call and talk to a live person. Someone answers, day or night. We listen to what’s happening, ask a few questions about your existing gate or the spot you’re planning for a new one, and schedule a time that works. No voicemail tag. No call center.
- 2
Site check and measurements. When we arrive, we check the gate’s condition, the posts, the hinge points, and the electrical situation. If it’s a new install, we measure the opening, check the ground grade, and talk through options with you on the spot.
- 3
Parts decision: OEM or quality aftermarket. For Linear control boards and safety sensors, we prefer OEM when the part is current and reasonably available. For actuators, hinges, and mechanical wear parts on older Linear systems, quality aftermarket components often outlast what the original equipment did. We explain the trade-off and let you decide. No hidden substitutions.
- 4
The installation itself. We prep the posts or set new ones, mount the opener, wire the controls, and dial in the travel limits and force settings. If your existing gate has a sag, we fix the hinge post rather than wrapping a chain around the picket and calling it done. If the panel is sound, we work with it. If it’s failing, we replace it. Repair-first, not replace-everything.
- 5
Force testing and safety check. Linear systems have photo eyes and obstruction sensing. We test them repeatedly, including a manual release test so you can get the gate open if the power’s out and you’re stuck on the wrong side of it.
- 6
Cleanup and the Done Right Promise. We leave the area cleaner than we found it, walk you through the operation, and hand you the 90-Day Done Right Promise in writing. If something’s off in the next three months, one call brings us back. No runaround.
What Linear Gate Installation Costs in University Park
Linear gate installation pricing in University Park breaks down like this.
- Pedestrian gate with Linear push-to-open actuator: $1,450 to $2,100 installed.
- Single driveway swing gate, standard Linear opener: $1,900 to $2,900 installed, depending on gate size and post condition.
- Double swing driveway gate with dual Linear openers: $3,200 to $4,300 for a proper pair that opens in sequence without binding.
- Linear slide gate, chain drive or rack drive: $2,600 to $4,000 installed, including the rail or chain.
- New Linear control board and receiver only: $280 to $520, including programming and antenna setup.
What moves the price is the gate itself. A rotted post or a binding hinge multiplies labor. A straight, plumb existing gate keeps the job quick and clean. University Park lots tend to have mature trees, which sometimes means trenching for conduit instead of a straight power run. That’s labor we’ll show you in the written estimate before you approve a dime.
Every Linear gate installation estimate is free, and the price we hand you is the price you pay. Call (936) 296-2568 and you’ll have a number before we leave the driveway.
Why University Park Homeowners Call Gatewood Fence & Gate for Linear Work
Hal Gatewood’s name is on the shop, and the shop is down the road. That’s the oldest accountability there is. We’ve been doing this since 2001, and we’re not going anywhere. When a Linear gate gives you trouble, the person who shows up is someone who has opened a hundred actuators just like yours and knows which board revision has the flaky relay. We don’t swap parts hoping one fixes it. We find the cause, fix the cause, and test until the gate cycles without a hiccup.
We also work on nine brands, so if your property has a Linear gate on the driveway and an old DoorKing or Ghost Controls on the back, one visit handles both. LiftMaster, Mighty Mule, all of it. Seniors and veterans get a permanent 10% discount no matter the job. And we offer a free second opinion on any written estimate you got from someone else. Bring us the paperwork. If the number’s fair, we’ll say so. If they’re padding it, we’ll tell you that too.
FAQs
As an independent Linear service provider, we install and service Linear equipment without voiding the manufacturer’s component warranty. If a part fails under Linear’s own warranty period, we’ll coordinate the replacement and handle the labor to get your gate moving again. The 90-Day Done Right Promise covers our workmanship regardless of what Linear’s warranty says.
Most standard Linear swing and slide gate installations in University Park are scheduled within the week, and many jobs that are just an opener swap can happen the same day depending on our schedule. The best way to get a straight answer is to call (936) 296-2568 and describe your gate. We’ll tell you when we can be there and what it’ll cost before we hang up.
If the gate frame is solid and the opener is under 12 years old, repair usually makes more sense. We fix the panel without the post and the post without the panel, and we never push a full replacement when a control board or a chain kit solves the problem. If the gate is rotted, the hinges are pulling out, and the opener has lived through two Lightning storms, we’ll be honest about replacement cost versus patching it up. Either way, you’ll see the numbers in writing before you decide.
For an emergency where your gate is stuck open or stuck shut and your driveway is blocked, call (936) 296-2568 right now. A live person answers around the clock. If we can’t be there today, we’ll tell you honestly when we can, and we won’t leave you guessing.
We run the low-voltage wiring, mount and wire the control box, and connect the opener to your existing power source. If your job requires new line-voltage wiring from the breaker panel, we’ll coordinate that part with a licensed electrician so the whole installation is done right. The price you’re quoted includes everything we’re responsible for, and we’ll flag any electrical line work separately before we start.
Call for a Free Linear Gate Installation Estimate in University Park
If you’ve got a Linear gate that won’t open or a driveway with no gate at all, call us at (936) 296-2568. Hal answers the phone or calls you back same day, every time. We’ll give you a written estimate based on your actual gate, your actual posts, and your actual ground, not a factory price sheet. Hand me your number and I’ll call you back, same day, every time.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving University Park and nearby areas.