Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Parts & Welding in University Park: What to Know First
Linear gate parts and welding in University Park is work we do regularly, and most jobs are done same week, often same day when a hinge or roller gives out. You’re not looking at a two-week wait while somebody orders a whole new gate from a warehouse. As an independent Linear service provider, we weld on site, source real parts that fit Linear’s slide and swing lines, and give you the price before we touch a single bolt.
This page is for University Park homeowners whose Linear gate has started sagging, dragging, or refusing to latch, and who want to know what’s actually wrong before someone sells them a replacement. If that’s you, call (936) 296-2568 and Hal Gatewood or one of his crew will walk you through what to look at.
Key Takeaways
- Linear gate repair in University Park usually means a hinge, roller, or post problem, not a whole new gate.
- We weld on site so the gate never leaves your driveway.
- Every Linear job carries our 90-Day Done Right Promise in writing.
- Free estimates, no trip charge inside the county, and $40 off any repair over $200.
How Linear Products Fail - and How We Fix Them
Linear builds gate openers and hardware that hold up well, but after years of University Park heat and the occasional hailstorm, certain parts wear in predictable ways. Here’s what we actually find in the field:
- The hinge post sags before the gate panel does. On Linear swing gates, especially the ornamental steel lines paired with Linear’s LS series operators, the post takes the weight and slowly leans. The gate starts dragging on the latch side and owners swear the panel warped. It didn’t. We cut out the old hinge weld, reset or replace the post, and re-weld the hinges so the gate swings clean. Fixing the panel without the post means you’ll fix it twice.
- Roller bearings seize on Linear SL slide gates, then the chain starts slapping. The SL slide operators pull a chain, and when a roller bearing freezes mid-track, the gate jerks instead of glides. We replace the rollers with sealed bearing units, check the track mounts, and weld any cracked rail sections right there in the driveway.
- Latch and lock strike plates drift out of alignment on Linear swing systems. Linear’s LSO and LDO swing operators rely on a clean mechanical close. When the latch catches hard, the opener reads resistance and reverses, leaving the gate open halfway. In University Park that’s an open invitation to the alley behind the house. We reset the strike, shim or re-weld the latch post, and run the opener through a full cycle before we call it done.
- Weld failures at the top hinge on larger Linear driveway gates. The Linear APeX series gets paired with heavy custom steel gates in some of the older University Park estates. The top hinge weld cracks first because the motor torques against it on every cycle. We grind it back to clean metal, re-weld, and add a gusset so it doesn’t crack the same way again.
- Aftermarket hinge kits from the box stores don’t fit Linear bolt patterns. We’ve pulled off plenty of hardware-store hinges somebody bolted on and shimmed with washers. It looks fine for six months, then the gate binds. We use OEM Linear hinges or fabricate a match in steel, not pot metal.
Our Linear Gate Parts & Welding Process
- 1
You call. A live person answers, 24/7. Not a voicemail, not a call center. Hal Gatewood’s number is the one on the shop door.
- 2
We show up on time. No trip charge inside the county. Background-checked, uniformed, and the person who shows up is the person who does the work.
- 3
We diagnose in front of you. Hal will show you the failing hinge, the seized roller, the cracked weld, and explain what it should look like instead. Show him the gate closing on its own and he’ll show you where it’s failing.
- 4
We make a parts call. OEM Linear when it’s a safety or warranty concern, quality aftermarket when it’s a roller or bracket and it makes sense for your budget. We tell you the difference before we order anything.
- 5
We weld and repair on site. The gate stays in your driveway. The truck carries a welder, stock steel, and the common Linear parts this area calls for. No hauling your gate off to some shop across town.
- 6
We test and clean up. The gate cycles smooth, the latch catches clean, and the opener doesn’t hiccup. We walk you through what we did, hand you the written 90-Day Done Right Promise, and leave the driveway cleaner than we found it.
What Linear Gate Parts & Welding Costs in University Park
Straight answer: most Linear gate parts and welding jobs in University Park land between $180 and $680, depending on what’s actually broken and how much welding the repair calls for.
| Linear Job | Typical Range |
|---|---|
| Hinge replacement, single gate | $180-$320 |
| Post replacement (steel, welded in place) | $380-$680 |
| Rail repair, slide gate (weld + reinforce) | $240-$480 |
| Roller replacement, slide gate (set of bearings) | $150-$300 |
| Latch and strike realignment | $160-$260 |
| Custom welding (cracked frame, gusset repair) | $150-$450 depending on scope |
What moves the price is steel thickness, access to the post base, and whether we’re repairing a weld or replacing the part entirely. Every price is quoted and agreed in writing before any work starts. Call (936) 296-2568 and we’ll come look, no charge for the estimate inside the county.
Why University Park Homeowners Call Gatewood Fence & Gate for Linear Work
Because Hal Gatewood’s name is on the shop, and the shop is down the road. He grew up not far from Goar Park and has been fixing gates in this part of Dallas since 2001. When a University Park homeowner calls about a Linear gate that won’t close at 9 p.m., the person who answers is either Hal or someone who works shoulder to shoulder with him every week. Not a call center in three states.
Every Linear job carries the 90-Day Done Right Promise in writing. If it’s not done right, we make it right. One call brings him back, no runaround. And when a Linear unit is beyond saving, we service the other brands you’re likely looking at: LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. Certified on all of them, so the recommendation you get is the honest one, not the one that pays a spiff.
FAQs
We use OEM Linear parts when a repair touches safety, mounting, or anything the warranty might cover. For wear items like rollers and some brackets, a quality aftermarket steel part often outlasts the original and costs less. We’ll tell you which one we recommend and why, and we’ll write the part source on your invoice so you know exactly what went on your gate.
Not sure what your gate needs? Call (936) 296-2568 and we’ll take a look free inside the county.
Most likely, yes. For repair and emergency calls we run same-day service in University Park and the surrounding area. Hal or one of his crew will give you a real window when you call, and the person who shows up will be the person you talked to. We don’t put you in a queue and we don’t make you wait through a recording.
If the post is sound and the panel is straight, repair is almost always the smarter money. A Linear opener paired with a steel gate can run another fifteen years if the hinges and rollers are right. We’ll tell you plainly if we think a full replacement makes more sense, and we’ll show you the numbers side by side. Repair-first is our default, not the pitch.
Welding on the gate panel itself won’t void a Linear opener warranty, because the opener and the gate are separate components. What voids warranties is modifying the opener’s control board, hacking the limit switches, or bypassing safety edges. We don’t do any of that. We weld the gate, not the motor.
Every job carries our 90-Day Done Right Promise in writing. If a hinge we welded loosens, a roller we replaced seizes, or a latch we set drifts out of alignment, we return and make it right at no charge. No fine print, no “up to” language. Hal Gatewood’s name is on the invoice next to that guarantee.
Want to talk through your Linear gate before we come out? Call (936) 296-2568. Hand us your number and we’ll call you back, same day, every time.
Call Gatewood Fence & Gate for Linear Gate Parts and Welding in University Park
If your Linear gate is sagging, dragging, or refusing to latch, don’t wait until it fails against a car or a kid on a bike. Call (936) 296-2568 for a free estimate. A live person answers, day or night. We’ll come to your University Park home, show you exactly what’s wrong, and give you a written price before any work starts. Seniors and veterans always get 10% off. $40 off any repair over $200, and no trip charge inside the county. The name is on the shop, the shop is down the road, and the work is done right the first time.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving University Park and nearby areas.