FAAC Gate Installation Nationwide | Gatewood Fence & Gate

FAAC Gate Installation in University Park: What to Know First

FAAC gate installation in University Park runs between $2,800 and $6,500 for most residential driveway gates, depending on whether you’re working with a single swing, double swing, or sliding setup. Hal’s shop typically turns a full FAAC install around in 2 to 4 working days once parts land, and the price you hear on the phone is the price on the invoice. We’re an independent FAAC service provider, not a factory authorized dealer, which means we tell you when a part is worth OEM money and when it isn’t.

Call (936) 296-2568

This page is for University Park homeowners who already own a FAAC operator or control board, or who are wondering if FAAC is the right call for the gate they’re planning. If you’re staring at a dead FAAC gate right now, call (936) 296-2568 and you’ll get a live person, not a voicemail tree.

How FAAC Products Fail - and How We Fix Them

FAAC builds solid operators, but around University Park we see the same handful of failure points pop up. Here’s what shows up most often and what we actually do about it:

• FAAC control boards killed by lightning or surges: The 455D and E024U boards handle a lot, but they don’t forgive a power surge in a Dallas thunderstorm. The board fries, the gate goes dead, and the display won’t respond. We check the surge protection on the incoming line every single FAAC install we touch, because a $60 suppressed outlet can save the $800 board.
• Capacitor failures on 391 and 400 series operators: These units have been running around Dallas for 15-plus years, and the run capacitor eventually gives out. The symptom is a gate that groans, moves halfway, then stops. A homeowner might think the motor’s done for, but it’s usually the capacitor, which is a service call not a replacement job.
• Limit switch drift after heavy usage: FAAC’s magnetic limit switches on the S418 and S450 slide operators can drift slightly if the gate gets knocked or the rack shifts. The gate starts slamming hard into the open stop or reversing short of the closed position. We reset the limits, torque the rack bolts, and the gate closes clean again.
• Hydraulic pump leaks on older FAAC swings: The 750 and 770 hydraulic operators are still common on older University Park estate gates. When the pump seal starts leaking, the gate slows down and leaves an oil line on the concrete. It needs new seals and fresh fluid, not a whole new operator, and that’s the kind of repair we’d rather do than a replacement.
• Photobeam alignment faults: FAAC’s photocells get knocked out of alignment by mower clippings bouncing off the posts or a kid on a bike clipping the housing. The gate refuses to close or reverses for no obvious reason. We don’t throw parts at it. We realign, clean the lenses, and if the housing is cracked, we replace just the photocell pair.

Our FAAC Gate Installation Process

Every FAAC job follows the same pattern. You’ll see it if you watch us work, and Hal’s happy to walk you through each step.

1. 1
   Call and assessment: You call, a live person answers, and we ask what the gate is doing or what you’re trying to build. We’ll set a time, and Hal or one of his guys will come look at the site in University Park.
2. 2
   Site measure and load check: We measure the gate leaf or leaves, check the hinge posts, look at the grade, and confirm the operator is sized right for the weight and wind load. FAAC operators are picky about duty cycle, and we don’t oversize or undersize.
3. 3
   Parts decision: We tell you straight what needs OEM FAAC parts and what can run on a quality aftermarket without voiding a warranty worth keeping. You see the number before anything gets ordered.
4. 4
   Install: We mount, wire, program the board, and set limits. If a post is leaning, we fix that first, because a FAAC operator can’t save a gate pulling off a bad hinge.
5. 5
   Cycle test: We run the gate through 15 to 20 open and close cycles, test the obstruction reversal, check the safety photoeyes, and adjust the closing force so it stops on an obstruction without stripping a gear.
6. 6
   Cleanup and the Promise: We sweep the debris, hand you the written 90-Day Done Right Promise, and walk you through what the display screen says. You’re not left guessing.

What FAAC Gate Installation Costs in University Park

Here’s an honest range of what we see in University Park:

• FAAC swing operator install (single leaf): $2,800 – $4,200
• FAAC sliding gate operator install (existing gate): $3,200 – $5,000
• Double swing gate with two FAAC operators: $4,800 – $6,500
• FAAC control board replacement (455D, E024U): $650 – $1,150 including programming
• Photobeam replacement pair: $160 – $300 installed

What moves the price is gate weight, post condition, and whether the existing wiring is still serviceable. We quote the job before work starts. You agree to the number. That’s the end of it. Call (936) 296-2568 for a free estimate, and remember we don’t charge a trip fee inside the county.

Why University Park Homeowners Call Gatewood Fence & Gate for FAAC Work

Hal Gatewood’s name is on the shop, and he’s the one who’ll be under your gate. We’ve been fixing and installing in this part of Dallas since 2001, and if a gate was hung wrong by somebody else, we’ll say so plainly and fix it right. Every job carries the 90-Day Done Right Promise in writing, not in a handshake. If it’s not right, one call brings us back.

We also service the other brands a homeowner might have on the property, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. So if one gate is FAAC and the other is a Mighty Mule on the back fence, you’re not juggling two companies. One crew, one trip, all brands. We answer the phone around the clock. You call, we answer, and we show up when we say, with a price you already have in hand.

FAQs